Section-00---002-003

MAIL ORDER: 1-800-265-2970 M-F 8AM-6PM EST EN/FR

SHOP ONLINE 24/7: WWW.ROYALDISTRIBUTING.COM

FREE SHIPPING ON ORDERS OVER $45 *

SUBSCRIBE TO OUR EMAILS FOR THE LATEST PRODUCTS AND DEALS!

STUD SELECTION GUIDE PENETRATION RECOMMENDATION FOR TRAIL RIDING IS 1/4” - 3/8” (0.250”-0.375”) Deviating from this recommendation can result in premature track wear, tunnel damage and/or loss of control. LUG HEIGHT STUD SIZE PENETRATION LUG HEIGHT

STUD PATTERNS Know the following concepts. The track’s centre belt controls acceleration. The 2 smaller outside track belts contribute to acceleration, but the more studs you put in these belts, the harder it is to corner. 1.Check allowable clearances between track and tunnel or heat exchangers. Factor in suspension travel. (Trail riders should NOT use studs that exceed 3/8” above the highest point of the track.) 2.Do not place studs under the tunnel protector strips (directly above slide rails on underside of tunnel). Tunnel protectors are vital and must not be subjected to damage from studs. 3.V-Shaped stud patterns with the least repetition work best. Studs should cover as many different lines in the ice as possible. 4.Studs closest to the slide rails provide the most effectiveness, because the sled weight is concentrated in this area.

NOTE: Tunnel and/or Heat Exchanger Protection is required with all traction products. It is your responsibility to ensure proper clearances and adequate protection. “SPT” SAFETY PUSH THROUGH CARBIDE STUDS True value makes it easy for anyone to afford. Features 80° carbide tip, 5/16” thread. Large 7/8” head. Silver colour. For 2-ply tracks. POWERPOINT CARBIDE STUD 60° carbide point for superior penetration and durability. Heat treated for strength/wear resistance. Large 1” head and 5/16” thread. Special tapered shank design provides the rigidity you need. For 2-ply tracks. POWERPOINT +PLUS CARBIDE STUD Designed for Camoplast Single Ply Tracks.

SNOW APPAREL

SNOW

APPAREL

STUD SIZE PENETRATION 0.910” 1.000” .320”-.350” 1.075” .390”-.420” 0.920” 1.000” .310”-.340” 1.075” .380”-.410” 1.000” 1.000” .220”-.250” 1.075” .300”-.330” 1.100” 1.175” .320”-.350” 1.250” 1.325” .320”-.350” 1.375” 1.450” .320”-.350” 1.500” 1.575” .300”-.350” 1.625” 1.740” .320”-.350” 1.750” 1.860” .320”-.350”

It features 60º carbide tip for aggressive penetration, and chamfered 1.160” head design and shorter shoulder area to reduce vibration and idler wheel wear. Use with new “Power Plate +PLUS” Backer Plates. 5/16” thread. For single ply tracks.

EYEWEAR

HELMETS

0.725” 0.875” .370”-.400” 0.750” 0.875” .345”-.375” 0.820” 0.875” .295”-.325” 0.920” .320”-.350” 1.000” .400”-.430” 0.850” 0.875” .245”-.275” 0.920” .310”-.340” 1.000” .370”-.400” 0.880” 0.875” .215”-.245”

HELMETS

EYEWEAR

LENGTH PART# .875” 14-281888* 1.000” 14-281893* 1.080” 14-281898* 1.187” 14-281903* 1.375” 14-281873 # 1.375” 14-281325^ 1.500” 14-281979 # 1.500” 14-281500^ 1.625” 14-281982 # 1.625” 14-281675^ 1.750” 14-281981 # 1.750” 14-281750^ 1.875” 14-260119 # 1.875” 14-281875^

APPAREL

NOTE: Tunnel and/or Heat Exchanger Protec tion is required with all traction products. It is your responsibility to ensure proper clearances and adequate protection.

•Install studs no closer than 3/4” from edges of track. •Avoid center of track - poor support in this area.

ATV/MX

LENGTH PART# 1.080” 14-996042* 1.187” 14-996046* 1.375” 14-996050 # 1.375” 14-291325^ 1.500” 14-996223 # 1.500” 14-291500^ 1.625” 14-996227 # 1.625” 14-291625^ 1.750” 14-996228 # 1.750” 14-996229^ 1.875” 14-996316 # 1.875” 14-291875^

ATV/MX

APPAREL

0.920” .270”-.300” 1.000” .350”-.380”

PROTECTIVE

IMPORTANT STUDDING INFORMATION We recommend that you install one stud first and turn the track ALL THE WAY AROUND to make sure that there is proper clearance and that the stud protrudes the proper amount over the lug, after checking... then proceed to install the remainder of the studs. 1/4”-3/8” of stud height (the portion of the stud protruding above the highest rubber portion of the track) is ideal for trail riding.

GEAR

LENGTH PART# .875” 14-260080* 1.000” 14-260084* 1.080” 14-260087* 1.187” 14-260091* 1.375” 14-260043 #

WOODY’S TRACK MARKER 14-891265

PROTECTIVE GEAR

* Includes Nyloc Nut. # Includes Power Tower Nuts ^No Nut use with Superlite Pro Series Backers

* Includes Nyloc Nut. # Includes Power Tower Nuts ^No Nut use with Superlite Pro Series Backers

*Includes Nyloc Nut. # Includes Power Tower Nuts

CASUAL

WEAR

STUD QTYS PART # 102-153 14-899756

WEAR

CASUAL

ROYAL BREAKS DOWN ALL STUDS AND WASHERS. NO NEED TO BUY KITS. WE ONLY SELL YOU WHAT YOU NEED.

DESCRIPTION 128" template 120-137” template

PLY PITCH WIDTH LENGTH 1-ply 2.52 14-15" 128

1-ply 2.86 15-16" 120-137 84-144 14-899755

CAMERAS COMMUNICATORS

POWER TOWER NUTS The extra support helps to eliminate stud bending and breaking without any additional weight. Use the Power Tower Lock-Nut in place of the standard nylon locknut on stud lengths of 1.375” and longer. .500” tall to be used with 1.375” to 1.500” studs. .750” tall to be used with 1.625” and longer studs. LENGTH PART# .500” 14-994988 .750” 14-996061

POWER PLATE 14-WAS-137 1.25” size for superior support. 0.145” thick aluminum. 5/16” hole. Radial lobe added, reduces wear and tear on the track and increases stud rigidity. For 2-ply tracks.

POWER PLATE DUAL 14-994356 0.145” thick aluminum. 5/16” hole. For 2-ply tracks.

129-137" w/ Quiet Pad Tech. template 2-ply 2.86 15"

129-137 90-144 14-898493

141" template

1-ply 3.00 15" 1-ply 2.86 20"

141 154

94-141 14-899757 108 14-899701

STUD TEMPLATE Studding templates for most track lengths and pitches, from the universal 15”x121” 2.52” pitch to the new 2.86” and 3.0” pitch run on the newer machines. Instructions included. Laminated cardboard.

154" Bearcat tempate 121-144" template 120-154" template

CAMERAS

2-ply 2.52 13.5-16" 121-144 96-198 14-899901 2-ply 2.86 15-16" 120-154 84-198 14-899900

COMMUNICATORS

ELECTRICAL CLUTCH/DRIVE

ELECTRICAL

CLUTCH/DRIVE

POWER PLATE +PLUS 14-WAS-139 To be used with POWER POINT +PLUS STUDS. Designed for Cam oplast Single Ply Tracks. Lightweight and durable shape features our innovative design for stud support. Reduces wear and tear on tracks, and receives the best benefits of both square and round backers. For single ply tracks.

POWER PLATE +PLUS DUAL 14-996184 0.145” thick aluminum. 5/16” hole. Larger size for use with 2 Powerpoint +Plus Studs. For single ply tracks.

TRACKS SUSPENSION

POWER ROUND PLATE 14-996322 1.455” size for superior support.

NE W

TRACKS

SUSPENSION

Aluminum with 5/16” hole. Radial lobe added, reduces wear and tear on the track and increases stud rigidity. For 2-ply & single ply tracks.

BRAKES

CABLES

CABLES

BRAKES

WINDSHIELDS

INTAKE/FUEL

SUPERLITE BACKERS Light-weight and vibrant colors. New engineered polymers-lighter than aluminum. Maintains excellent strength. “Single+” backer: 1.450” square backer to be used on all tracks with any 5/16” carbide stud. “Double+” backer: 1.450” x 2.562” used for single ply studs on single ply tracks only. “Double” backer: for use on two ply tracks using regular “Power Point” type carbide studs.

SUPERLITE PRO SERIES BACKERS Lightest weight and best traction available. Includes the support nut

INTAKE/FUEL

WINDSHIELDS

PRO SERIES BACKER INSTALL TOOL 14-994303 A must have tool. Holds the single Pro Series Backers while installing the studs. Allows you to safely apply pressure to the backer and also keep the backer oriented properly. SUPERLITE PRO SERIES BACKERS COLOR SINGLE DOUBLE DOUBLE+ Black 14-996266 14-996264 14-996286 White 14-996297 14-996265 14-996287 Red 14-996267 14-996240 14-996289 Orange 14-996268 14-996239 14-996290 Green 14-996269 14-996301 14-996291 Yellow 14-996293 14-996270 14-996292 Hi-Viz Yellow 14-996294 14-996298 Hi-Viz Blue 14-996295 14-996299 Hi-Viz Green 14-996296 14-996300 Purple 14-996271 14-996272 molded directly into the backer. Tested by top snowcross and cross country racers. Can be used with all brands of 5/16” studs 1.325” and taller. Backers are 3/4” tall. Doubles can only be used with standard studs. Not for single ply tracks. “Double +” are for use with “+PLUS” studs for Single ply tracks.

SKIS STEERING

SKIS

STEERING

Singles can be used with standard or “+PLUS” studs.

PERFORMANCE

ENGINE PARTS

ENGINE PARTS

PERFORMANCE

TRACTION

CONTROL

CONTROL

TRACTION

LUGGAGE ACCESSORIES

LUGGAGE

SUPERLITE BACKERS COLOR DOUBLE SINGLE + DOUBLE + Black 14-996131 14-996082 14-996105 Blue 14-996083 Green 14-996133 14-996084 14-996107 Red 14-996134 14-996085 14-996108 White 14-996135 14-996086 14-996109 Yellow 14-996136 14-996087 14-996110 Orange 14-996209 14-996203 14-996200

ACCESSORIES

TOOLS / TRAILER

LUBRICANTS

TOOLS / TRAILER LUBRICANTS

ATV / UTV

MOTO

ATV / UTV MOTO

*Some conditions apply. Prices andmisprints are subject to change. Due to supply and price volatility fromour suppliers, prices are not shown for some items. See our website or call for assistance.

284

285

GIVE THE GIFT OF CHOICE!

FOLLOW US!

RETAIL STORES: GUELPH (519) 822-7081 INNISFIL (705) 431-9364 SUDBURY (705) 566-8111 WHITBY (905) 619-8000 KANATA (613)663-3167

GIFT CARD$