Winter 2023 Catalogue

MAIL ORDER: 1-800-265-2970 M-F 8AM-6PM EST EN/FR

SHOP ONLINE 24/7: WWW.ROYALDISTRIBUTING.COM

STUD SELECTION GUIDE PENETRATION RECOMMENDATION FOR TRAIL RIDING IS 1/4” - 3/8” (0.250”-0.375”) Deviating from this recommendation can result in premature track wear, tunnel damage and/or loss of control. LUG HEIGHT STUD SIZE PENETRATION LUG HEIGHT

STUD PATTERNS Know the following concepts. The track’s centre belt controls acceleration. The 2 smaller outside track belts contribute to acceleration, but the more studs you put in these belts, the harder it is to corner. 1.Check allowable clearances between track and tunnel or heat exchangers. Factor in suspension travel. (Trail riders should NOT use studs that exceed 3/8” above the highest point of the track.) 2.Do not place studs under the tunnel protector strips (directly above slide rails on underside of tunnel). Tunnel protectors are vital and must not be subjected to damage from studs. 3.V-Shaped stud patterns with the least repetition work best. Studs should cover as many different lines in the ice as possible. 4.Studs closest to the slide rails provide the most effectiveness, because the sled weight is concentrated in this area.

SNOW APPAREL

STUD SIZE PENETRATION 0.910” 1.000” .320”-.350” 1.075” .390”-.420” 0.920” 1.000” .310”-.340” 1.075” .380”-.410” 1.000” 1.000” .220”-.250” 1.075” .300”-.330” 1.100” 1.175” .320”-.350” 1.250” 1.325” .320”-.350” 1.375” 1.450” .320”-.350” 1.500” 1.575” .300”-.350” 1.625” 1.740” .320”-.350” 1.750” 1.860” .320”-.350”

EYEWEAR

HELMETS

0.725” 0.875” .370”-.400” 0.750” 0.875” .345”-.375” 0.820” 0.875” .295”-.325” 0.920” .320”-.350” 1.000” .400”-.430” 0.850” 0.875” .245”-.275” 0.920” .310”-.340” 1.000” .370”-.400” 0.880” 0.875” .215”-.245”

MX APPAREL

NOTE: Tunnel and/or Heat Exchanger Protec tion is required with all traction products. It is your responsibility to ensure proper clearances and adequate protection.

•Install studs no closer than 3/4” from edges of track. •Avoid center of track - poor support in this area.

0.920” .270”-.300” 1.000” .350”-.380”

PROTECTIVE

IMPORTANT STUDDING INFORMATION We recommend that you install one stud first and turn the track ALL THE WAY AROUND to make sure that there is proper clearance and that the stud protrudes the proper amount over the lug, after checking... then proceed to install the remainder of the studs. 1/4”-3/8” of stud height (the portion of the stud protruding above the highest rubber portion of the track) is ideal for trail riding.

GEAR

WOODY’S TRACK MARKER 14-891265

CASUAL

WEAR

STUD QTYS PART # 102-153 14-899756

DESCRIPTION 128" template 120-137” template

PLY PITCH WIDTH LENGTH 1-ply 2.52 14-15" 128

1-ply 2.86 15-16" 120-137 84-144 14-899755

CAMERAS COMMUNICATORS

129-137" w/ Quiet Pad Tech. template 2-ply 2.86 15"

129-137 90-144 14-898493

141" template

1-ply 3.00 15" 1-ply 2.86 20"

141 154

94-141 14-899757 108 14-899701

STUD TEMPLATE Studding templates for most track lengths and pitches, from the universal 15”x121” 2.52” pitch to the new 2.86” and 3.0” pitch run on the newer machines. Instructions included. Laminated cardboard.

154" Bearcat tempate 121-144" template 120-154" template

2-ply 2.52 13.5-16" 121-144 96-198 14-899901 2-ply 2.86 15-16" 120-154 84-198 14-899900

ELECTRICAL CLUTCH/DRIVE

TRACKS SUSPENSION

BRAKES

CABLES

WINDSHIELDS

INTAKE/FUEL

SKIS STEERING

PERFORMANCE

ENGINE PARTS

TRACTION

CONTROL

LUGGAGE ACCESSORIES

TOOLS / TRAILER

LUBRICANTS

ATV / UTV

MOTO

*Some conditions apply. Prices andmisprints are subject to change. Due to supply and price volatility fromour suppliers, prices are not shown for some items. See our website or call for assistance.

286

GIVE THE GIFT OF CHOICE!

FOLLOW US!

GIFT CARD$