2025/26 Digital Winter Parts Catalogue

FREE SHIPPING ON ORDERS OVER $89 *

SUBSCRIBE TO OUR EMAILS FOR THE LATEST PRODUCTS AND DEALS! STUD PATTERNS Know the following concepts. The track’s centre belt controls acceleration. The 2 smaller outside track belts contribute to acceleration, but the more studs you put in these belts, the harder it is to corner. 1.Check allowable clearances between track and tunnel or heat exchangers. Factor in suspension travel. (Trail riders should NOT use studs that exceed 3/8” above the highest point of the track.) 2.Do not place studs under the tunnel protector strips (directly above slide rails on underside of tunnel). Tunnel protectors are vital and must not be subjected to damage from studs. 3.V-Shaped stud patterns with the least repetition work best. Studs should cover as many different lines in the ice as possible. 4.Studs closest to the slide rails provide the most effectiveness, because the sled weight is concentrated in this area.

STUD SELECTION GUIDE PENETRATION RECOMMENDATION FOR TRAIL RIDING IS 1/4” - 3/8” (0.250”-0.375”) Deviating from this recommendation can result in premature track wear, tunnel damage and/or loss of control. LUG HEIGHT STUD SIZE PENETRATION LUG HEIGHT

STUD SIZE PENETRATION 0.910” 1.000” .320”-.350” 1.075” .390”-.420” 0.920” 1.000” .310”-.340” 1.075” .380”-.410” 1.000” 1.000” .220”-.250” 1.075” .300”-.330” 1.100” 1.175” .320”-.350” 1.250” 1.325” .320”-.350” 1.375” 1.450” .320”-.350” 1.500” 1.575” .300”-.350” 1.625” 1.740” .320”-.350” 1.750” 1.860” .320”-.350”

ELECTRICAL

CLUTCH/DRIVE

0.725” 0.875” .370”-.400” 0.750” 0.875” .345”-.375” 0.820” 0.875” .295”-.325” 0.920” .320”-.350” 1.000” .400”-.430” 0.850” 0.875” .245”-.275” 0.920” .310”-.340” 1.000” .370”-.400” 0.880” 0.875” .215”-.245”

NOTE: Tunnel and/or Heat Exchanger Protec tion is required with all traction products. It is your responsibility to ensure proper clearances and adequate protection.

•Install studs no closer than 3/4” from edges of track. •Avoid center of track - poor support in this area.

TRACKS

SUSPENSION

0.920” .270”-.300” 1.000” .350”-.380”

IMPORTANT STUDDING INFORMATION We recommend that you install one stud first and turn the track ALL THE WAY AROUND to make sure that there is proper clearance and that the stud protrudes the proper amount over the lug, after checking... then proceed to install the remainder of the studs. 1/4”-3/8” of stud height (the portion of the stud protruding above the highest rubber portion of the track) is ideal for trail riding.

CABLES

BRAKES

THIN NYLOC NUTS DESCRIPTION PART # 7mm hole 14-NYL-5000 5/16” hole (short nut) 14-NYL-5020 5/16” hole (tall nut) 14-NYL-5020-01

INTAKE/FUEL

WINDSHIELDS

ALUMINUM DISCS WE RECOMMEND these washers for use with any stud. The premium washer available today. Machined high quality aluminum. Backside is counter-bored to insure a flat, snug fit on today’s thin tracks. 1-3/16” diameter, unequaled rigidity. 1-3/8” Diameter x 1/4” Tall. 0.140 material thickness that works on any 5/16” stud. Anodized Premium heat-treated aluminum. ATS ALUMINUM WASHER 14-WAS-140

ATS “SHO GUN II” CARBIDE STUD Large 1” head - increased rigidity and holding strength to prevent studs from pulling through track. Stainless steel body, 5/16” shank for superior strength, reduced wear and rust resistant. Large silver brazed carbide insert greatly increases life of stud. For single ply & 2-ply tracks. Includes nyloc nut. LENGTH PART#

SKIS

STEERING

.875” 14-ATS-8750 1.00” 14-ATS-1000 1.075” 14-ATS-1075 1.325” 14-ATS-1325 1.450” 14-ATS-1450 1.520” 14-ATS-1520

DESCRIPTION 7mm / 1/4” hole

PART # 14-WAS-126 14-WAS-127 14-WAS-147

5/16” hole

5/16” hole OVERSIZED 1-3/8” dia.

ENGINE PARTS

PERFORMANCE

IGRIP TRACK STUDS What type of snowmobiler are you? Whether you be a pleasure seeker who is looking for increased traction and security in the trails or a rip shedding nut job on a quest for high performance aggressive traction, we’ve got you covered. Whether you have an old and worn track or a brand new one, iGrip has a stud to suit your need. These studs offer you the advantage of being silent, cost effective and very easy to install. Being light weight, they won’t add excessive weight to your track and being deeply threaded into the lugs rubber, they pose little to no danger to coolers as they rarely come out. These studs will provide you with an increased feeling of stability, control and security in all situations, icy or not. Our Standard Studs (ST), provide better all around traction especially in strategic areas of the trail such as curves and ice patches. They provide security, traction and overall increased performance and durability. Our Shouldered Studs, (SS), on the other hand are designed for aggressive riding on all trail and ice surfaces for the high performance enthusiasts. NOTE: The SS models are not recommended for the Cobra 1.352 and Ripsaw II tracks as they are too narrow and flexible. PART # LUG LENGTH QTY SERIES TRACK STUDS HEIGHT 14-SS11200R .500”+ 11mm/.433” 200 SS 14-ST11200 .500”+ 11mm/.433” 200 ST

CONTROL

TRACTION

Less danger to coolers vs. standard studs!

LUGGAGE

ACCESSORIES

14-ST20150R 1”+ 20MM/.787” 150 ST 14-ST24150R 1.25”+ 24MM/.945” 150 ST 14-ST24200R 1.25”+ 24MM/.945” 200 ST 14-ST25150R 1.25”+ 25MM/.984” 150 ST 14-ST25200R 1.25”+ 25MM/.984” 200 ST 14-SS28150R 1.25”+ 28MM/1.102” 150 SS 14-SS28200R 1.25”+ 28MM/1.102” 200 SS 14-SS28250R 1.25”+ 28MM/1.102” 250 SS 14-SS32150R 1.5”+ 32MM/1.25” 150 SS 14-SS32200R 1.5”+ 32MM/1.25” 200 SS 14-SS32250R 1.5”+ 32MM/1.25” 250 SS

For 136” tracks and smaller the 150 packs work. For 137”-143” tracks use the 200 pack. For 144”+ tracks use the 250 pack.

INDEX TOOLS / TRAILER LUBRICANTS

ST20/24 SS28/32 Track lug thickness should be no less than 3/16” / 5mm.

INSTALL TOOL INCLUDED!

TIRE STUDS 14-ST11150 14-ST15150 14-ST18150

.500”+ 11mm/.433” 150 ST .625”+ 15mm/.590” 150 ST .750”+ 18mm/.708” 150 ST

181

RETAIL STORES: GUELPH (519) 822-7081 INNISFIL (705) 431-9364 SUDBURY (705) 566-8111 WHITBY (905) 619-8000 KANATA (613)663-3167