2020 Fall/Winter Catalogue

STUD SELECTION GUIDE PENETRATION RECOMMENDATION FOR TRAIL RIDING IS 1/4” - 3/8” (0.250”-0.375”) Deviating from this recommendation can result in premature track wear, tunnel damage and/or loss of control. LUG HEIGHT STUD SIZE PENETRATION LUG HEIGHT

STUD PATTERNS Know the following concepts. The track’s centre belt controls acceleration. The 2 smaller outside track belts contribute to acceleration, but the more studs you put in these belts, the harder it is to corner. 1. Check allowable clearances between track and tunnel or heat exchangers. Factor in suspension travel. (Trail riders should NOT use studs that exceed 3/8” above the highest point of the track.) 2. Do not place studs under the tunnel protector strips (directly above slide rails on underside of tunnel). Tunnel protectors are vital and must not be subjected to damage from studs. 3. V-Shaped stud patterns with the least repetition work best. Studs should cover as many different lines in the ice as possible. 4. Studs closest to the slide rails provide the most effectiveness, because the sled weight is concentrated in this area.

SNOW

APPAREL

STUD SIZE PENETRATION 0.910 1.000” .320”-.350” 1.075” .390”-.420” 0.920 1.000” .310”-.340” 1.075” .380”-.410” 1.000 1.000” .220”-.250” 1.075” .300”-.330” 1.100 1.175” .320”-.350” 1.250 1.325” .320”-.350” 1.375 1.450” .320”-.350” 1.500 1.575” .300”-.350” 1.625 1.740” .320”-.350”

0.725 0.875” .370”-.400” 0.750 0.875” .345”-.375” 0.820 0.875” .295”-.325” 0.920” .320”-.350” 1.000” .400”-.430” 0.850 0.875” .245”-.275” 0.920” .310”-.340” 1.000” .370”-.400” 0.880 0.875” .215”-.245”

HELMETS

EYEWEAR

• Install studs no closer than 3/4” from edges of track. • Avoid center of track - poor support in this area.

NOTE: Tunnel and/or Heat Exchanger Protec- tion is required with all traction products. It is your responsibility to ensure proper clearances and adequate protection.

MX

APPAREL

0.920” .270”-.300” 1.000” .350”-.380”

IMPORTANT STUDDING INFORMATION We recommend that you install one stud first and turn the track ALL THE WAY AROUND to make sure that there is proper clearance and that the stud protrudes the proper amount over the lug, after checking... then proceed to install the remainder of the studs. 1/4”-3/8” of stud height (the portion of the stud protruding above the highest rubber portion of the track) is ideal for trail riding.

CLUTCH DRIVE ELECTRICAL CASUAL WEAR CAMERAS & T

WOODY’S TRACK MARKER 14-891265 $13.99

COMMUNICATORS

STUD TEMPLATE Studding templates for most track lengths and pitches, from the universal 15”x121” 2.52” pitch to the new 2.86” and 3.0” pitch run on the newer machines. Instructions included. Laminated cardboard.

DESCRIPTION 121” Universal 128” template 128” template 128” template 129" template 120-137” template 120-137” template

PLY PITCH WIDTH LENGTH QTYS PART # PRICE

2-ply 2.52 15"

121 48-192 14-899179 19.99

2-ply 2.52 13.5-15" 128 51-153 14-899177 29.99

1-ply 2.52 14-15" 2-ply 2.52 13.5" 1-ply 2.86 15-16"

128 102-153 14-899756 23.99 128 96-144 14-899182 19.99 129 90-135 14-898494 29.99

SKIS STEERING WINDSHIELDS TRACKS SUSPENSION INTAKE FUEL BRAKES CABLES

2-ply 2.86 14-16" 120-137 84-192 14-899366 29.99

1-ply 2.86 15-16" 120-137 84-144 14-899755 29.99 129-137” w/ Quiet Pad Tech. template 2-ply 2.86 15" 129-137 90-144 14-898493 29.99 136-144” Long Track template 2-ply 2.52 15-16" 136-144 108-171 14-899181 29.99 141” template 1-ply 3.00 15" 141 94-141 14-899757 29.99 154” Bearcat tempate 1-ply 2.86 20" 154 108 14-899701 34.99

TUNNEL/HEAT EXCHANGER PROTECTORS Provide protection for your snowmobile tunnel and heat exchangers against costly traction stud contact. Easy installation and easy to modify length.

3/4” Aluminum 14-1000 $42.99 PR POLARIS YAMAHA 1” Aluminum 14-1014 $42.99 PR

04-200 ARCTIC CAT

04-199-01 POL/YAM

POLARIS YAMAHA

DESCRIPTION

PART # PRICE # PCS

04-199-07 04-199-10 SKI-DOO

ARCTIC CAT 52" x 5/8"

Most other Arctic Cats 27.99 each POLARIS All Indy Models with running board heat exchangers, All Fan Cooled Indy. YAMAHA ‘97-04 Liquid Cooled Models, All Fan Cooled Models. All years. 52” x 1” Deep 04-199-01 25.99 each SKI-DOO All Models ‘85-09 (ex. REV XP/XS) w/liquid cooled engines-slide in type 44-1/4” x 3/4” Deep (136"+ req 3) 04-199-07 17.99 each 48” x 1” Deep 04-199-10 19.99 each REV XP/XS ‘08-UP 57.5" x 3/4" Deep 137" tracks (cut to length for 120" tracks) Fits Sidewinder and Thundercat. 04-199-21 29.99 each 04-200

50” Long

04-199-21 REV XP

ENGINE PARTS

PERFORMANCE

CONTROL

TRACTION

HEAT EXCHANGER/BULKHEAD GUARDS With acceleration or rapid deceleration, the track studs can cut into the front cooler or bulkhead. These guards maintain the safety margin to help prevent this damage.

LUGGAGE

ACCESSORIES

SKI-DOO 14-1009 $16.99 DSA Chassis Coolant Hose Protector

POLARIS 14-1013 $34.99 Fits all:Standard/Evolved Chassis. May differ slightly from image.

YAMAHA 14-1017 $59.99 Fits ‘97-03 Pro Action Chassis (VMax/SRX/Venture) ex. ‘00-01 Venture 700. Simple installation, no need to remove track or drive shaft.

ATV/MOTO TOOLS/TRAILER LUBRICANTS

263